Showing posts with label Boat electronics GPS. Show all posts
Showing posts with label Boat electronics GPS. Show all posts

Saturday, August 7, 2010

Crazy mouse is dead, more from PC purgatory.


Since I wrote the story  "PC" purgatory, I had looked everywhere, for a Crazy Mouse problem solution and had received a lot of advice, but none of it worked to date. I asked for help and got it. My friend Alan had forwarded several possible options, and among them was this  link as a subset of  a young fellows home page
.
















I posted the possible solution on Panbo's forum, and Henning Durr gave me encouraging words regarding the viability of the solution. I installed the registry patch today, and it worked perfectly. No more crazy mouse, with three serial GPS's plugged in. No more disabling serial ballpoints, it just worked. This was an XP system by the way, and although I think it will work with Vista, and Windows 7 tread carefully, and I think sobriety is required while doing this, we don't want an ARI (alcohol related incident)  to occur you know.

The solution is simple, and consists of  using Regedit in the PC to change two numbers. The changes are below:

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\sermouse]
"Start"=dword:00000004 (the 4 was a 3 before)

[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Services\sermouse]
"Start"=dword:00000004 (the 4 was a 3 before)

If you want to go back, just change the "4" to a "3", and you can have the crazy mouse back. By the way, your serial mouse will no longer work, so get a USB mouse before you start this, if you need to. I just went into the registry and manually changed the values. It took about ten minutes to do. If you are faint of heart, find a 12 year old kid to do it for you. Why does it have to be so complicated?

Thanks JamieZX, clever patch, and a good problem solution.


Sunday, July 18, 2010

What a dumb idea, stupid, why I oughta.....


This should have been a simple job. A Raymarine E-120 wasn't getting a fix, and the investigation begins. Let's check the power, and antenna wiring. The wiring is by the book, and we have good power. The Seatalk cable is plugged in, so let's make sure that it is the master, and it is. I do a software upgrade, and follow it with two factory resets, and still, the GPS page is blank. So where is the GPS? This is the question of the hour.

















It's not on the top of the T-top, and it's not in the electronics box. I looked under the combings, nope, I chase the antenna cable, and find the antenna must be mounted on top of the electronics box. You can see the wire passing through the hole. I had to clear the wiring away just to see this much.
















So I reach my hand up to feel where it was, and I couldn't feel it or see it, because someone at the factory had covered the entire area with two part foam, I guess to seal the two small holes passing though the electronics box. The actual GPS was fully encapsulated in several inches of foam. This is one of the areas in a boat, where you can look, or you can get one hand in, but you can't do both at the same time.
















It took about an hour to excavate around the GPS enough to free it from the box. Two part foam is very tenacious and the GPS was well adhered to the electronics box, but with the judicious application of numerous explicatives, and some hard digging with my fingers, the GPS finally was removed. The point of the exercise was to see what the little LED on the Raystar 125 was telling me. It couldn't tell me anything, because the chemicals in the two part foam, had obscured the clear port you look through to see the LED status.

















I happened to have a new GPS in the truck, and when I plugged it in, the unit immediately started to blink happy green, and within a minute, we had a position fix. So what was wrong with the original unit, we will never know, maybe the foam out-gassed fumes that got into the unit, or maybe stuff just happens.

















Recapping the moral of the story, there had to be many other ways to seal the two small penetrations through this box, and I think the worst possible way to do it was to use two part foam. It made pulling new wires through the existing holes almost impossible, it was ugly, unprofessional, crudely done, and I'm going to revoke the boat rigging licence of who ever did this, if I ever catch him. I do have my sealing suggestion below, and don't confuse this with 3M 5200, or I will revoke your licence also. 

Monday, November 23, 2009

The angry wrathful technology gods at work (Click pic for a better view)


















This is a case of the angry gods at work. This box is connected to sealed rubber covered switch pads on the dash, and is programmed to turn on chartplotters, stereos, pumps, and all of the other things on the boat. The boat is four years old now, and the box has failed, taking the operation of 16 pieces of equipment with it.

The box was made by Carling, who sold, or transfered it to another company. They promptly redesigned it, and discontinued production of the original box. There are no spare parts, no programmers for it, no wiring diagrams, no nothing period. The only option here is to remove the digital pads from the console, cover the holes with a overlay panel, and install 16 switches. Actually there is another box that controlled another 8 switches, so you might as well do all 24 switches at the same time. The boat builder feels bad about it, but can't do anything about it. It would have been cheaper to build the boat with 24 switches in the first place. Sometimes simple is best in a highly corrosive salt water environment.